- HOW DO I FIX ENTERNET DRIVER CONTROLLER ON INSPRION 560 HOW TO
- HOW DO I FIX ENTERNET DRIVER CONTROLLER ON INSPRION 560 BLUETOOTH
In my Dell Inspiron N5110 I had a regular 2.5″ SATA hard drive installed. I had some trouble disconnecting the hard drive because it was glued to the motherboard with some adhesive rubber.įirst I had to lift up the left side of the hard drive a little bit and separate it from the motherboard and after that disconnect from the motherboard. Remove two screws securing the hard drive mounting bracket. Here you can access the cooling fan assembly and hard drive. NOTE: if your Dell Inspiron N5110 has a failed DC jack it’s easier to replace the entire board than the jack itself. Separate the DC jack board form the motherboard and remove it. Remove one screw securing the DC jack board to the motherboard. The I/O board and both speakers are attached to the laptop base assembly and can be removed if necessary. The I/O board has the following ports on it: USB ports, audio jacks, Ethernet (LAN) port. Unplug the speaker cable from the motherboard.Ĭarefully lift up the right side of the motherboard and disconnect it from the I/O board.
Remove four screws securing the motherboard. If you want to replace the DC jack board, it’s necessary to remove the motherboard too. The cooling fan can be accessed only when the motherboard removed.
HOW DO I FIX ENTERNET DRIVER CONTROLLER ON INSPRION 560 BLUETOOTH
When the palmrest assembly is removed you can access the CMOS battery and Bluetooth module. Remove the plastic cover located under the display assembly. Move the connector towards the display and unplug it from the motherboard.
HOW DO I FIX ENTERNET DRIVER CONTROLLER ON INSPRION 560 HOW TO
Here’s how to disconnect the video cable. Simply lift up the gold connector and unsnap it from the wireless card. Here’s how to disconnect the wiereless card antenna cable. Remove four screws securing the display hinges. Insert a piece of plastic between the palmrest and bottom cover and separate them.Ĭontinue lifting up and removing the palmrest assembly.ĭisconnect the video cable from the motherboard.ĭisconnect both antenna cables from the wireless card. Now you can start separating the palmrest assembly from the bottom cover. Lift up the connector retainer and pull the cable. You disconnect all three connectors the same way we did it in steps 10 and 11. Remove four screws securing the palmrest assembly.ĭisconnect the following cables from the motherboard: You can remove the rubber cover with a sharp object.Īfter that remove both screws found under those covers. There are two rubber screw seals in the upper left and right corners (yellow circles). Now you can pull the keyboard cable from the connector. The retainer will open up at a 90 degree angle and the connector will be unlocked. Lift up the left side of the brown retainer with your fingernail. It’s necessary to unlock the connector and release the cable before removing the keyboard. Now you can access the keyboard cable connector. Turn the keyboard upside down and place it on the palmrest. Lift up the upper part of the keyboard and move it towards the display. Now insert your fingers under the keyboard and carefully pull it up. When the latch pushed in, lift up the keyboard a little bit so the latch doesn’t snap back in place.ĭo the same with all three remaining latches. Push on the latch with a small flathead screwdriver. You’ll find four spring loaded latches securing the keyboard. There is no screw securing the DVD drive. Pull the DVD drive to the left and remove it. This laptop will take up to 8GB (2x4GB) DDR3-12800 SODIMM memory modules.
It’s not necessary to disconnect the memory module from the motherboard for the purpose of my guide. In my Dell Inspiron N5110 I had only one memory module installed. Under the memory cover you’ll find two memory slots. Remove one screw securing the memory cover. UPDATE: I just published a new guide explaining how to replace the LCD screen on a Dell Inspiron 15R N5110. STEP 19-20: Disconnecting and removing the display assembly. STEP 13-18: Removing the palmrest assembly. STEP 5-12: Disconnecting and removing the keyboard. STEP 1-4: Accessing both memory slots and removing DVD drive. Here are some major disassembly steps I will go through: I will disassemble the base and remove the motherboard in order to access the DC jack board and hard drive.
0 kommentar(er)
